High holding force
Reliable clamping
Without pre-stamping
OEM quality
Grip insert carbide
Grip insert for form fit clamping of raw material. The grip insert deforms the workpiece surface during the clamping process and thus increases the holding force of the clamping location. For or use with reversible stepped jaws MZC (page 166) or custom made clamping jaws.
Material
Carbide
Finish
Grinded
Scope of delivery
1 Pair grip inserts carbide
Grip insert ZG
Grip insert for form fit clamping of raw material. The hardened surface of the grip insert
deforms the workpiece surface during the
clamping process and thus increases the
holding force of the clamping location. The
applied coating protects the grip insert from
premature wear. For use with pendulum jaws
MZC or custom made clamping
jaws.
Material
Steel
Finish
Hardened, coated
Scope of delivery
2 Grip inserts with screw
Prism jaws
Hardened and grinded prism jaws for clamp-
ing round workpieces.
Material
Steel
Finish
Hardened, grinded
Scope of delivery
2 Prism jaws
Practical advice
Customized prism jaws
In order to satisfy different customer’s
demands we can also deliver
customized prism jaws.
Short clamping jaws 75°
Through the undercut at the jaws, the workpiece is held securely during machining. Only 3 mm clamping depth are necessary.
Material
Steel
Finish
Hardened, grinded
Scope of delivery
2 Short clamping jaws 75°
Note
Form cutters to prepare your workpieces are available on request.
Working steps
1. Sawing raw materia
2. Machining dovetail contour
3. Clamping raw material
Grip jaws
For form fit clamping of raw material. The hardened surface of the grip jaws deforms the workpiece surface during the clamping process and thus increases the holding force of the clamping location. The applied coating protects the grip jaws from premature wear.
Material
Special tool steel
Finish
Hardened, coated
Scope of delivery
2 Grip jaws
Practical advice
Best results with workpieces up to 1100 N/mm 2 material strength.
Clamping jaws, soft
The soft clamping jaws can be machined and
fitted on the workpiece.
Material
Steel (16MnCr5)
* Steel, rust-resistant
Finish
Soft, pre-machined
Scope of delivery
2 Clamping jaws, soft
Note
Aluminum, plastic or brass version
available on request.
Step jaws, rough with coating
For form fit clamping of high-strength raw material. The hardened surface of the clamping jaws deforms the workpiece surface during the clamping process and thus increases the holding force of the clamping location. The applied coating protects the grip jaws from premature wear.
Material
Steel
Finish
Hardened, coated
Scope of delivery
2 Step jaws, rough with coating
Practical advice
Best results with workpieces with more than 1100 N/mm2 material strength and sturdy material surface.
Step jaws with carbide coating
The hardened, ground and then carbide coated step jaws are used for clamping of ground finished parts or in the second set-up. High holding force through increased friction factor. The workpiece surface will not be damaged.
Material
Steel
Finish
Hardened, carbide coated
Scope of delivery
2 Step jaws with carbide coating
Practical advice
Best results with workpieces in mold and die production. 1,5 – 2,0 times higher friction factor or holding force than smooth clamping surfaces.
Pull-down pendulum jaws
The pendulum jaws allow raw material clamping of cast, molded as well as unparallel sawed workpieces. With the pull-down pendulum jaws, angular misalignments of several millimetres can be rectified. The clamping surfaces are rough serrated.
Material
Steel
Finish
Hardened, grinded
Scope of delivery
1 Pull-down pendulum jaw
1 Fixed jaw
2 Support rails
Top jaws MZE
For use together with all standard jaws type MZE as well as customer designed jaws. The top jaws allow the use of short cuting tools especially with small workpieces.
Material
Steel
Finish
Hardened, grinded
Scope of delivery
2 Top jaws MZE
Top jaws MZS
For changing a centre-clamping vise type A into type B.
Material
Steel
Finish
Hardened, grinded
Scope of delivery
2 Top jaws MZS
Stepped grip jaws
For form fit clamping of raw material. The hardened surface of the grip jaws deforms the workpiece surface during the clamping process and thus increases the holding force of the clamping location.
Material
Special tool steel
Finish
Hardened
Scope of delivery
2 Stepped grip jaws
Practical advice
The stepped grip jaws are especially suitable for large clamping width.
Best results with workpieces up to 1100 N/mm2 material strength and sturdy material surface.
Pull-down pendulum jaws
The pendulum jaws allow raw material clamping of cast, molded as well as unparallel sawed workpieces. With the pull-down pendulum jaws, angular misalignments of several millimetres can be rectified. The clamping surfaces are rough serrated.
Material
Steel
Finish
Hardened, grinded
Scope of delivery
1 Pull-down pendulum jaw
1 Fixed jaw
2 Support rails
Stepped jaws Type 1
One-piece jaw, inward stepped.
Material
Steel
Finish
Hardened, grinded
Scope of delivery
3 Stepped jaws
Stepped jaws Type 2
One-piece jaw, outward stepped.
Material
Steel
Finish
Hardened, grinded
Scope of delivery
3 Stepped jaws
Soft unstepped jaws
One-piece jaw, soft.
Material
Steel
Finish
Soft
Scope of delivery
3 Soft unstepped jaws
Soft block jaws
The soft block jaws can be machined or fitted on the workpiece respectively.
Material
Steel (16MnCr5)
Finish
Soft, pre-machined
Scope of delivery
2 Soft block jaws
Note
Aluminum, plastic or brass version available on request.
Reversible stepped jaws
Universal stepped jaws reversible, with
three ground clamping stages and threaded
mounting hole for fixed stop. The hardened
and ground jaws are used for clamping of
finished parts or in the second setup.
Material
Steel
Finish
Hardened, grinded
Scope of delivery
2 Reversible stepped jaws
Reversible stepped jaws with carbide grip inserts
For form fit clamping of raw material. The carbide grip-inserts of the clamping jaws deform
the workpiece surface during the clamping
process and thus increases the holding force
of the clamping location. The grip inserts can
be replaced, if necessary.
Material
Steel, carbide (grip inserts)
Finish
Hardened, grinded
Scope of delivery
2 Reversible stepped jaws with carbide grip inserts
Practical advice
Best results with workpieces with more
than 1100 N/mm2 material strength
and sturdy material surface.
Reversible stepped jaws with clamping inserts, rough with coating / carbide coating
Universal stepped jaws reversible, with integrated clamping inserts, ground clamping
stages and threaded mounting hole for fixed
stop. The clamping insert can be mounted on
the reversible steped jaws depending on the
application. For clamping of finished parts
there is also a smooth clamping stage
included. The clamping inserts can be
replaced, if necessary.
Material
Steel
Finish
Hardened, grinded and
coated / carbide coated
Scope of delivery
2 Reversible stepped jaws with clamping
inserts
1. Side
For form fit clamping of high-strength raw
material. The hardened and coated surface
of the clamping jaws deforms the work-piece surface during the clamping process
and thus increases the holding force of the
clamping location.
Practical advice
Best results with workpieces with more
than 1100 N/mm2 material strength
and sturdy material surface.
2. Side
For clamping of grinded material. High holding force through increased friction factor.
The workpiece surface will not be damaged.
Practical advice
Best results with workpieces in mold
and die production. 1,5 – 2,0 times
higher friction factor or holding force
than smooth clamping surfaces.
Reversible stepped jaws with carbide coating
Universal stepped jaws reversible, with three
ground and then carbide coated clamping
stages and threaded mounting hole for fixed
stop. For clamping of grinded material. High
holding force through increased friction factor.
The workpiece surface will not be damaged.
Material
Steel
Finish
Hardened, carbide coated
Scope of delivery
2 Reversible stepped jaws with carbide coating
Practical advice
Best results with workpieces in mold
and die production. 1,5 – 2,0 times
higher friction factor or holding force
than smooth clamping surfaces.
Pendulum jaws with grip inserts
The pendulum jaws with grip inserts allow
raw material clamping of cast, molded as well
as unparallel sawed and round workpieces.
With the pendulum jaws, angular misalignments of several millimetres can be rectified.
The applied coating protects the grip inserts
from premature wear. The grip inserts can be
flexibly mounted on the pendulum jaws and
replaced if necessary.
Material
Steel
Finish
Hardened, grinded and coated
(grip inserts)
Scope of delivery
2 Pendulum jaws with grip inserts
Practical advice
Best results with workpieces up to
1100 N/mm2 material strength.
Prism jaws
Hardened and grinded prism jaws for clamping round workpieces.
Material
Steel
Finish
Hardened, grinded
Scope of delivery
2 Prism jaws
Practical advice
Customized prism jaws In order to satisfy different customer’s demands we can also deliver customized prism jaws.
Reversible grip jaws uncoated
For form fit clamping of raw material. The
hardened surface of the grip jaws deforms
the workpiece surface during the clamping
process and thus increases the holding force
of the clamping location. The applied coating
protects the grip jaws from premature wear.
Material
Special tool steel
Finish
Hardened
Hardened and coated
Scope of delivery
2 Reversible grip jaws
Practical advice
Best results with workpieces up to
1100 N/mm2 material strength.