Version for EHS 65 and EHS 65 N. The angle settings from 0° - 60° can be made with gauge blocks according to the sine principle. The vise can be inserted into the guide on the spindle or front side and slidably from the middle. Material Tempered tool steel Finish Surface hardened Scope of delivery 1 Sine table including fixing material

Version for EHS 65 and EHS 65 N. The angle settings from 0° - 60° can be made with gauge blocks according to the sine principle. The clamping device holder can also be rotated by 360°. Material Tempered tool steel Finish Surface hardened Scope of delivery 1 Sine table with swivel base including fixing material Notice Optionally, the sine tables EHS can be equipped with adapter plates for centre-clamping vise, three-jaw chuck or universal faceplate

This precision EDM vise is specially designed for use on wire EDM machines. The mounting hole pattern allows mounting on a 40 mm and 50 mm hole grid using an M8 screw. Material Magnetizable Chrome steel, rust-resistant Finish Completely hardened Completely precision grinded Preloaded and completely sealed roller bearing Accuracy Square-accuracy 0,005 mm Parallel-accuracy 0,01/300 mm Scope of delivery 1 Vise with operating instructions 1 Operating key Operation Mechanical

This indexing unit with collet chuck is specially designed for use on wire-EDM machines provided. Through the mounting holes mounting on hole pattern 40 mm and 50 mm by M8 screws is possible. Indexing via indexing plate with 72 positions, the indexing positions by 360°-scale and nonius interim. Material Magnetizable chrome steel, rust-resistant Finish Completely hardened Completely precision grinded Fully sealed precision rolling bearings Accuracy Square-accuracy 0,005mm Parallel-accuracy 0,003mm Concentricity 0,01mm Indexing precision ±2' Scope of delivery 1 Indexing unit with operating instructions Accessories Collet ER 32 (470E) Ø2 - 20 mm Operation Mechanical Collet Collet ER 32 (470 E), Ø2 – 20 mm

This indexing unit with three-jaw chuck is specially designed for use on wire-EDM machines provided. Through the mounting holes mounting on hole pattern 40 mm and 50 mm by M8 screws is possible. Indexing via indexing plate with 72 positions, the interim indexing positions by 360° scale and nonius. Material Magnetizable chrome steel, rust-resistant Finish Completely hardened Completely precision grinded Fully sealed precision rolling bearings Accuracy Square-accuracy 0,005 mm Parallel-accuracy 0,003mm Concentricity 0,01mm Indexing precision ±2' Scope of delivery 1 Indexing unit with operating instructions Operation Mechanical Three-jaw chuck 100 mm

This indexing unit is specially designed for use on wire-EDM machines provided. Through the mounting holes mounting on hole pattern 40 mm and 50 mm by M8 screws is possible. Indexing via indexing plate with 72 positions, the interim indexing positions by 360° scale and nonius. Material Magnetizable chrome steel Rust-resistant Finish Completely hardened Completely precision grinded Fully sealed precision rolling bearings Accuracy Square-accuracy 0,005mm Parallel-accuracy 0,003mm Concentricity 0,01mm Indexing precision ±2' Scope of delivery 1 Indexing unit with operating instructions Operation Mechanically

Indexing unit with collet chuck for toolmaking and prototyping. Material Tool steel Body cast iron Finish Surface hardened Mounting surface precision grinded Accuracy Concentricity 0.01mm Parallel-accuracy 0,003 mm Scope of delivery 1 Indexing unit with operating instructions 1 Indexing plate with 24 positions Notice Indexing plates with 20 and 36 positions on request Fixing holes for grid holes 20-M10 Version with three-jaw chuck on request Operation Mechanical Collet Collet 385 E, Ø3 – 26 mm

Mounting with two grip insets and crew M6 Prepared for chip coding on request Central flushing hole Mounted on 3R-Macro 3R-651,7E-S Material Steel, rust-resistant Scope of delivery Round clamp including contact screws Notice Exchangeable grip insets EROWA versions upon request

Ø2 - 20 mm Collet for use in the indexing unit VA. Scope of delivery 1 Set in wooden case Note Rust-resistant stainless steel version upon request. Different sizes available separately on request

For precise dressing of grinding wheels using the Sine dresser. Material Steel Finish Completely hardened Completely precision grinded Scope of delivery 1 Sine-grinding wheel dresser Operation Mechanical Cross feed Up to 60mm Angle 0-60°

Precision spindle vise for grinding, milling and checking tasks. Pivoting around the transverse axis: SKS 1 Pivoting around the longitudinal axis: SKS 2. Different sizes available on request.

Ø3 – 26 mm collet for use in the direct dividing head. Material Sreel Finish Hardened, grinded Scope of delivery 1 Collet Notice Different sizes available separately on request

The basic structure of the punch grinders type RSG is conform with the concentricity gages. They are used on flat as well as tool sharpening machines. Punching dies, ejector pins, stop pins, extraction dies and short step drills can be ground in a cylindrical or any other form. The work piece will be rolled up between three centerless rolls. Thereby the concentricity will be 0.002 mm. The robust construction with preloaded precision bearings of the supporting roll is constructed for longevity. For the length limit variable stops will be set up Strong Points Robust design with pre-loaded rolling bearings Simple handling Universal use on surface grinders Material Steel Attachments made of aluminium Finish Burnished, black anodized Hardened and precision grinded rollers Scope of delivery 1 Punch grinder with variable stops Accessories Electric drive Accessories available on request Supporting roll on the driving side (two supporting rolls and two additional pulleys)

Prism jaws with a vertical prism on the front and a smooth clamping surface on the back. Material Tool steel Finish Completely hardened Completely precision grinded Accuracy Square-accuracy 0,003 mm Parallel-accuracy 0,002 mm Scope of delivery 1 Prism jaw

The clamping rails are used to increase the span. Material Tool steel Finish Completely hardened Completely precision grinded Accuracy Square-accuracy 0,003 mm Parallel-accuracy 0,002 mm Scope of delivery 2 Clamping rails

Adjustable fixed stop for screwing onto the fixed jaw. Material Tool steel Finish Completely hardened Completely precision grinded Scope of delivery 1 Adjustable stop including fixing material

Base plate for holding one or more vices of the EHS type on the processing machine. Material Tempered tool steel Finish Surface hardened Scope of delivery 1 Locating plate including fixing material

Rotary plate for vises type EHS. The angle can be adjusted using a 180° scale. Werkstoff Tempered tool steel Finish Surface hardened Scope of delivery 1 Rotary table including fixing material

The angle vise is used for gauge-precise machining and checking of surfaces and angle surfaces. The two-dimensional angle adjustment takes place via vernier scales and fine adjustment screw. Size 70 with 3' nonius, size 120 with 5' nonius. Horizontally rotatable by 360°. Vertically pivotable by 2×60°. Material Tool steel Finish Completely hardened Completely precision grinded Accuracy Square-accuracy 0,003 mm Parallel-accuracy 0,003 mm Scope of delivery 1 Vise with perating instructions 1 Operating key Notice Special version with three-jaw chuck available on request Operation Mechanical

The SN sine vise is intended for grinding and checking surfaces and angular surfaces from 0° to 46°. Material Tool steel Finish Completely hardened Completely precision grinded Accuracy Square-accuracy 0,005 mm Parallel-accuracy 0,003 mm Scope of delivery 1 Vise with operating instructions 1 Operating key Activity Mechaical

The sine carrier with magnetic clamping plate is used for gauge-precise processing and checking of surfaces and angle surfaces. Scope of delivery 1 sine carrier with operating instructions SPNSI version The SPNSI version swivels about the longitudinal axis to a maximum angle of 45°. SPNSIL version The SPSD version swivels about the longitudinal axis to a maximum angle of 45°and about the transverse axis to a maximum angle of 30°. SPSID version The SPSD version swivels about the longitudinal axis to a maximum angle of 45°and about the transverse axis to a maximum angle of 30°.

The precision vises of the EHS design are intended for use on grinding machines, jig boring machines and other precision machines, and as universal clamping devices in the measuring and testing room. The vises can be used overleaf on all four contact surfaces and offer an extremely large span. The clamping jaw contains a horizontally ground-in V-block. pull-down system The movable clamping jaw is pulled down by the clamping pressure that occurs. This causes a significantly reduced lifting of the workpiece during processing. No knocking down of the workpiece, no "rattling". Strong Points Gauge accurate clamping All-round precision ground Pull-down system No lifting of the workpiece No vibration during machining Material Tool steel Finish Completely hardened Completely precision grinded Accuracy Square-accuracy 0,003 mm Parallel-accuracy 0,002 mm Scope of delivery 1 Vise with operating instructionsth 1 Cranked handle Operation Mechanical

For lifting and transporting automation pallets. Lightweight construction for effortless movement and maneuvering of the load. Features Build-in charger Central brake and steering system Remote control with cable Battery and charging indicator Safety clutch Load capacity max. 150 kg, 600 mm in front (300 kg, 600 mm in front optional) max. 85 kg, 1000 mm in front max. 70 kg, 1200 mm in front Travel Vertical-travel ca. 1400 mm Horizontal-travel ca. 1000 mm Horizontal-travel in front of wheels ca. 500 mm Lifting speed 135 mm/s Batteries 2×12 V 17 Ah Time to charge 5 hours (from empty Own weight 65 kg (110 kg) Scope of delivery 1 Mobile pallet lift with operating instructions